BOLTON GATE CO LTD

WATERLOO STREET
BOLTON
LANCASHIRE BL1 2SP

Tel: 01204 871001
Fax: sales@boltongate.co.uk

Company Logo

These files are provided by the manufacturer. While Building Products Index takes every care to ensure the information is correct and up to date, we cannot be held liable for any out of date or incorrect information in them. You should check with the supplier before specifying or purchasing products.

BOLTON GATE CO LTD: Fire Shutter - Fireroll Acoustic - Insulated Fire Shutter
Bolton Gate Company’s Fireroll range of roller shutters is the most comprehensive available in the market.  A further  addition is the Fireroll Acoustic E120 which combines fire resistance with a high degree of sound reduction. During extensive testing at Salford University Department of Acoustics and two Fire Test Laboratories, the door achieved a sound reduction of a maximum 25.2dB (at 2000Hz) with a 22dB Rw coupled with a rating of E120 when tested in accordance with EN1634-1. In keeping with the same testing, the shutter is also rated EW90 or EW120 dependent on size for face fixed arrangements.  A special double curtain arrangement is also available which reduces sound transmission further to a maximum of 39.1dB (at 2000Hz) with a 32dB Rw. OperationAll shutters are electrically operated by a 230-volt nominal single phase or 400-volt nominal three phase Speedsafe motor mounted on one endplate and have adjustable limit switches incorporated to stop the shutter at the end of each travel.  A pull cord and hand chain are provided for use in the event of power failure. Standard operation is via a low-level push button station with emergency stop button.  In a fire condition, gravity failsafe closing is activated by a 24-volt DC signal (0.37 amps) from the client’s fire alarm panel to the auto reset solenoid which releases the motor brake and is backed up by a fusible link. A safety brake is supplied to comply with the safeguarding requirements of EN 12604. CurtainShutter curtains are constructed from 100mm high flat section continuously interlocked galvanised steel laths which are securely held in place by steel end locks. Each lath is infilled with fire resisting acoustic material.  Bottom RailThe bottom rail comprises a standard lath fitted with a galvanised steel trim section. Side GuidesVertical guides are formed from galvanised steel double rebate channels and are supplied with suitable profiles for fixing to the structure.RollerThe roller is constructed from seamless steel tube of adequate diameter to resist deflection and held in bearings or cups attached to the endplates  EndplatesZinc plated mild steel of appropriate thickness relative to door size and supplied with angles for fixing to the structure. Coil CasingA galvanised steel coil casing is supplied to maintain the fire seal at the head. FinishFireroll Acoustic E120 is supplied with most parts galvanised as standard. Where non-galvanised parts are utilised, these are finished with one coat of primer paint Maximum Sizes7000mm wide x 5000mm high12000mm wide – height dependent (please contact our sales team to discuss)   WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 50kgs/m². Options· Heat / smoke detectors.· Audio visual warning.· Factory finish comprising white plastisol to internal curtain face (coil side) with a polyester powder coat finish to external face from a range of standard RAL colours.· Grade 304 or 316 stainless steel.· Double curtain arrangement with increased Rw.    Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Fire Shutter - Fireroll E120
Bolton Gate Company offers probably the most comprehensive range of modern fire resisting shutters available on the market today. The Fireroll E120 two-hour fire rated shutter is designed to provide fire compartmentation with security, durability and reliability in mind. This fire shutter will satisfy the needs of large or complex packages as well as meeting the most stringent safety and insurance requirements.  All Bolton Gate fire doors and shutters are tested and assessed by officially recognised and competent authorities.  OperationSuitable for all sizes of shutters, the Speedsafe drive unit has a 230-volt nominal single phase or 400-volt nominal three phase geared induction motor with an electromagnetic brake, limit switches, release unit, a built-in starter panel and low-level push button station with emergency stop button. In a fire condition, gravity failsafe closing is activated by a 24-volt DC signal (0.37 amps) from the client’s fire alarm panel to the auto reset solenoid which releases the motor brake and is backed up by a fusible link. A safety brake is supplied to comply with the safeguarding requirements of EN 12604. Manual operation in the event of a power loss is achieved by releasing a pull cord to close the shutter under controlled descent and a hand chain to open.  CurtainShutter curtain is constructed from continuously interlocked 76mm curved section steel laths which are securely held in place by end locks. Lath thicknesses vary dependent upon opening size.  Bottom RailBottom rails are galvanised, and roll formed into a Tee section. Side GuidesChannel section galvanised mild steel guides with slotted fixings for expansion in a fire are fixed to the jambs with continuous steel angles.  RollerThe roller is made from seamless tube of sufficient diameter and wall thickness to resist deflection and is supported in bearings mounted on each endplate. EndplatesFabricated from steel plate and prepared to accept the coil casing. Securely bolted to steel fixing angles which are drilled for attachment to the structure at the correct centres.  Coil CasingA galvanised steel coil casing is supplied to maintain the fire seal at the head. FinishFireroll E120 is supplied in a galvanised finish as standard. Where non-galvanised parts are utilised, these are finished with one coat of primer paint. Maximum Sizes7000mm wide x 7000mm high as standard12000mm wide - height dependent (please contact our sales team to discuss) WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 50kgs/m². Options· Heat/smoke detectors· Audio visual warning· Polyester powder coated finish to a range of standard RAL colours.· Grade 304 or 316 stainless steel. · Obstruction detection (light curtain or safety photocell).  Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Fire Shutter - Fireroll E120
Bolton Gate Company offers probably the most comprehensive range of modern fire resisting shutters available on the market today. The Fireroll E120 two-hour fire rated shutter is designed to provide fire compartmentation with security, durability and reliability in mind. This fire shutter will satisfy the needs of large or complex packages as well as meeting the most stringent safety and insurance requirements.  All Bolton Gate fire doors and shutters are tested and assessed by officially recognised and competent authorities.  OperationSuitable for all sizes of shutters, the Speedsafe drive unit has a 230-volt nominal single phase or 400-volt nominal three phase geared induction motor with an electromagnetic brake, limit switches, release unit, a built-in starter panel and low-level push button station with emergency stop button. In a fire condition, gravity failsafe closing is activated by a 24-volt DC signal (0.37 amps) from the client’s fire alarm panel to the auto reset solenoid which releases the motor brake and is backed up by a fusible link. A safety brake is supplied to comply with the safeguarding requirements of EN 12604. Manual operation in the event of a power loss is achieved by releasing a pull cord to close the shutter under controlled descent and a hand chain to open.  CurtainShutter curtain is constructed from continuously interlocked 76mm curved section steel laths which are securely held in place by end locks. Lath thicknesses vary dependent upon opening size.  Bottom RailBottom rails are galvanised, and roll formed into a Tee section. Side GuidesChannel section galvanised mild steel guides with slotted fixings for expansion in a fire are fixed to the jambs with continuous steel angles.  RollerThe roller is made from seamless tube of sufficient diameter and wall thickness to resist deflection and is supported in bearings mounted on each endplate. EndplatesFabricated from steel plate and prepared to accept the coil casing. Securely bolted to steel fixing angles which are drilled for attachment to the structure at the correct centres.  Coil CasingA galvanised steel coil casing is supplied to maintain the fire seal at the head. FinishFireroll E120 is supplied in a galvanised finish as standard. Where non-galvanised parts are utilised, these are finished with one coat of primer paint. Maximum Sizes7000mm wide x 7000mm high as standard12000mm wide - height dependent (please contact our sales team to discuss) WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 50kgs/m². Options· Heat/smoke detectors· Audio visual warning· Polyester powder coated finish to a range of standard RAL colours.· Grade 304 or 316 stainless steel. · Obstruction detection (light curtain or safety photocell).  Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Fire Shutter - Fireroll E30
Part of Bolton Gate Company’s extensive range of fire products, the Fireroll E30, Fire Resisting Roller Shutter, is an electrically operated fire barrier that delivers a thirty-minute fire rating which has been specifically designed to provide compartmentation for smaller openings. Offering an extremely neat and compact but secure and robust design its attractive close fitting lath curtain makes it eminently suitable for all applications but particularly that of servery type openings or where aesthetic appearance is of paramount importance. OperationThe Speedsafe drive unit has a 230-volt nominal single-phase geared induction motor with an electromagnetic brake, limit switches, release unit, a built-in starter panel and low-level push button station with emergency stop button. The design provides a fail-safe system which will close the shutter automatically in the event of a fire situation. Activation is via a signal from the fire alarm system to an auto reset solenoid which, when activated, releases the motor brake allowing the shutter to close by gravity with a controlled descent. A safety brake is supplied to comply with the safeguarding requirements of EN12604. Manual operation in the event of a power loss is achieved by releasing a pull cord to close the shutter under controlled descent and a hand chain to open. CurtainThe shutter curtain is constructed from continuously interlocking 51mm flat faced laths securely held in place by endlocks. Bottom RailThe bottom rail is also formed from a reinforced lath to give uniformity of appearance. Side GuidesVertical guides are fabricated from cold rolled galvanised steel channels 50 x 25mm which are attached to the supporting structure.  RollerThe roller is made from seamless steel tube of sufficient diameter and wall thickness to resist deflection and is supported in bearings mounted on each endplate. EndplatesFabricated from steel plate and prepared to accept the coil casing. Securely bolted to steel fixing angles which are drilled for attachment to the structure at the correct centres. Coil CasingCoil and motor casings are constructed from galvanised steel and cover all moving parts at high level. FinishFireroll E30 is supplied in a galvanised finish as standard.Where non-galvanised parts are utilised, these are finished with one coat of primer paint. Maximum Sizes4000mm wide x 2500mm high WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 25kgs/m². Options· E60 and E120 fire ratings. · Audible and/or visual alarms.· Polyester powder coated finish to a range of standard RAL colours.· Grade 304 or 316 stainless steel.· Obstruction detection (light curtain or safety photocell).  Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Fire Shutter - Fireroll E30
Part of Bolton Gate Company’s extensive range of fire products, the Fireroll E30, Fire Resisting Roller Shutter, is an electrically operated fire barrier that delivers a thirty-minute fire rating which has been specifically designed to provide compartmentation for smaller openings. Offering an extremely neat and compact but secure and robust design its attractive close fitting lath curtain makes it eminently suitable for all applications but particularly that of servery type openings or where aesthetic appearance is of paramount importance. OperationThe Speedsafe drive unit has a 230-volt nominal single-phase geared induction motor with an electromagnetic brake, limit switches, release unit, a built-in starter panel and low-level push button station with emergency stop button. The design provides a fail-safe system which will close the shutter automatically in the event of a fire situation. Activation is via a signal from the fire alarm system to an auto reset solenoid which, when activated, releases the motor brake allowing the shutter to close by gravity with a controlled descent. A safety brake is supplied to comply with the safeguarding requirements of EN12604. Manual operation in the event of a power loss is achieved by releasing a pull cord to close the shutter under controlled descent and a hand chain to open. CurtainThe shutter curtain is constructed from continuously interlocking 51mm flat faced laths securely held in place by endlocks. Bottom RailThe bottom rail is also formed from a reinforced lath to give uniformity of appearance. Side GuidesVertical guides are fabricated from cold rolled galvanised steel channels 50 x 25mm which are attached to the supporting structure.  RollerThe roller is made from seamless steel tube of sufficient diameter and wall thickness to resist deflection and is supported in bearings mounted on each endplate. EndplatesFabricated from steel plate and prepared to accept the coil casing. Securely bolted to steel fixing angles which are drilled for attachment to the structure at the correct centres. Coil CasingCoil and motor casings are constructed from galvanised steel and cover all moving parts at high level. FinishFireroll E30 is supplied in a galvanised finish as standard.Where non-galvanised parts are utilised, these are finished with one coat of primer paint. Maximum Sizes4000mm wide x 2500mm high WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 25kgs/m². Options· E60 and E120 fire ratings. · Audible and/or visual alarms.· Polyester powder coated finish to a range of standard RAL colours.· Grade 304 or 316 stainless steel.· Obstruction detection (light curtain or safety photocell).  Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Fire Shutter - Fireroll E60
Part of Bolton Gate Company’s extensive range of fire products, the Fireroll E60, Fire Resisting Roller Shutter, is an electrically operated fire barrier that delivers a sixty-minute fire rating which has been specifically designed to provide compartmentation for smaller openings. Offering an extremely neat and compact but secure and robust design its attractive close fitting lath curtain makes it eminently suitable for all applications but particularly that of servery type openings or where aesthetic appearance is of paramount importance. OperationThe Speedsafe drive unit has a 230-volt nominal single-phase geared induction motor with an electromagnetic brake, limit switches, release unit, a built-in starter panel and low-level push button station with emergency stop button. The design provides a fail-safe system which will close the shutter automatically in the event of a fire situation. Activation is via a signal from the fire alarm system to an auto reset solenoid which, when activated, releases the motor brake allowing the shutter to close by gravity with a controlled descent. A safety brake is supplied to comply with the safeguarding requirements of EN12604. Manual operation in the event of a power loss is achieved by releasing a pull cord to close the shutter under controlled descent and a hand chain to open. CurtainThe shutter curtain is constructed from continuously interlocking 51mm flat faced laths securely held in place by endlocks. Bottom RailThe bottom rail is also formed from a reinforced lath to give uniformity of appearance. Side GuidesVertical guides are fabricated from cold rolled galvanised steel channels 50 x 25mm which are attached to the supporting structure. RollerThe roller is made from seamless steel tube of sufficient diameter and wall thickness to resist deflection and is supported in bearings mounted on each endplate. EndplatesFabricated from steel plate and prepared to accept the coil casing. Securely bolted to steel fixing angles which are drilled for attachment to the structure at the correct centres. Coil CasingCoil and motor casings are constructed from galvanised steel and cover all moving parts at high level. FinishFireroll E60 is supplied in a galvanised finish as standard.Where non-galvanised parts are utilised, these are finished with one coat of primer paint. Maximum Sizes4000mm wide x 2500mm high WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 25kgs/m². Options· E30 and E120 fire ratings· Audible and/or visual alarms· Polyester powder coated finish to a range of standard RAL colours· Grade 304 or 316 stainless steel.· Obstruction detection (light curtain or safety photocell).  Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Fire Shutter - Fireroll E60
Part of Bolton Gate Company’s extensive range of fire products, the Fireroll E60, Fire Resisting Roller Shutter, is an electrically operated fire barrier that delivers a sixty-minute fire rating which has been specifically designed to provide compartmentation for smaller openings. Offering an extremely neat and compact but secure and robust design its attractive close fitting lath curtain makes it eminently suitable for all applications but particularly that of servery type openings or where aesthetic appearance is of paramount importance. OperationThe Speedsafe drive unit has a 230-volt nominal single-phase geared induction motor with an electromagnetic brake, limit switches, release unit, a built-in starter panel and low-level push button station with emergency stop button. The design provides a fail-safe system which will close the shutter automatically in the event of a fire situation. Activation is via a signal from the fire alarm system to an auto reset solenoid which, when activated, releases the motor brake allowing the shutter to close by gravity with a controlled descent. A safety brake is supplied to comply with the safeguarding requirements of EN12604. Manual operation in the event of a power loss is achieved by releasing a pull cord to close the shutter under controlled descent and a hand chain to open. CurtainThe shutter curtain is constructed from continuously interlocking 51mm flat faced laths securely held in place by endlocks. Bottom RailThe bottom rail is also formed from a reinforced lath to give uniformity of appearance. Side GuidesVertical guides are fabricated from cold rolled galvanised steel channels 50 x 25mm which are attached to the supporting structure. RollerThe roller is made from seamless steel tube of sufficient diameter and wall thickness to resist deflection and is supported in bearings mounted on each endplate. EndplatesFabricated from steel plate and prepared to accept the coil casing. Securely bolted to steel fixing angles which are drilled for attachment to the structure at the correct centres. Coil CasingCoil and motor casings are constructed from galvanised steel and cover all moving parts at high level. FinishFireroll E60 is supplied in a galvanised finish as standard.Where non-galvanised parts are utilised, these are finished with one coat of primer paint. Maximum Sizes4000mm wide x 2500mm high WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 25kgs/m². Options· E30 and E120 fire ratings· Audible and/or visual alarms· Polyester powder coated finish to a range of standard RAL colours· Grade 304 or 316 stainless steel.· Obstruction detection (light curtain or safety photocell).  Fire-resisting roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: Insulated Roller Shutter
Bolton Gate Company’s Insulated Rolling Shutter offers the benefit of a multipurpose solution when there is a requirements for sound or thermal insulation, high security or even weather resistance. The combined attributes can easily assist in compliance with the environment demands that are increasing relevant today. A wide range of options including drive systems, operating controls and also various finishes effectively allow our Clients to specify a bespoke, high quality, yet cost effective solution to sit their needs.  The Insulated Rolling Shutters doors have been used extensively on projects both in the UK and worldwide where their integral strength and robust design assures continued reliability and trouble free operation and optimum design life. OperationTubular Motor· To suit 230-volt nominal, 1 phase supply.· External safety brake.· Low level keyswitch Direct Drive Motor· To suit 400-volt nominal, 3 phase supply· Integrated safety brake.· Open, close, stop push buttons within low level control panel. Manual overrides are provided for use in event of power failure. CurtainThe shutter curtain is constructed using continuously interlocked 95mm deep galvanised steel foam bonded insulated laths secured by endlocks. Bottom RailAn extruded aluminium bottom rail is provided complete with rubber weather seal. Side GuidesVertical side guides are formed from rolled galvanised steel in a double rebate profile and fitted with twin brush strips. Full height angles are provided for mounting the structure. RollerThe roller is constructed from seamless steel tube of adequate diameter to resist deflection and held in bearings attached to the endplates.  EndplatesFormed using prime painted mild steel of thickness to suit the respective opening size. CasingsA galvanised steel coil casing and motor casing are provided as standard to close off the operating mechanism and complete the aesthetic appearance of the door. On the tubular motor system, the coil casing is a more compact chamfered design. FinishGalvanised steel is the default finish but please refer to Options below for alternatives. Maximum SizesTubular Motor option: 6m wide x 3m highDirect Drive option: 10m wide x 10m high(Please contact our sales team there is a requirement beyond these dimensions). WeightVaries with opening size dependent on lath/barrel/casing requirements but approximately 45kgs/m². Options· Polyester powder coat finish.· Plastisol finish to curtain, remaining components with a polyester powder coat finish.· Grade 304 or 316 stainless steel.· Double glazed vision panels. · Additional electrical controls e.g.: - - Keyswitches - Radio controls - Radar / loop detectors / photocells. - Timer closing.  Roller shutters

Published [30/03/2026]

BOLTON GATE CO LTD: SecRoll SR1, SR2 & SR3 Security Shutters - High Security Roller Shutter
Bolton Gate offer a complete range of Security Rated options from SR1 through to SR5 rating. The latest addition to our portfolio, are the SecRoll Security Roller Shutters offering A1, B3 & C5 security classifications equivalent to SR1, SR2 & SR3 respectively.  Providing a choice of ratings, these bespoke high security rolling shutters manufactured here in the UK are designed to provide flexibility for our Clients with a wide range of opening sizes and specification options including thermal and acoustic capabilities. We are proud to confirm that our security shutters are registered in the BRE Global ‘Red Book Live’ confirming our products have been rigorously tested, assessed and approved by LPCB (Loss Prevention Certification Board) and that also the same high standard and quality production is maintained through the process of regular audits.C5 Rated SecRoll SR3:Operation:Tubular motor:To suit 230-volt nominal, 1 phase supply.External safety brake.Low level keyswitchDirect Drive Motor:To suit 400-volt nominal, 3 phase supplyIntegrated safety brake.Open, close, stop push buttons within low level control panel.Arrangement:Internally face fixed to brick, block, concrete or steel (i.e. rigid structures).Locking:A pair of side guide mounted pin locks are provided.Over 3500 mm clear width, a centrally mounted ground lock (complete with padlock) is also provided (2no if >7000 mm). Size parameters:Maximum (width x height): 10 x 10 m (Direct drive motor); 7 x 4 m high (Tube motor).Minimum (width x height):1 x 1 m.Weight:Varies with opening size dependent on lath/barrel/casing requirements but approximately 45 kgs/m².  B3 Rated SecRoll SR2:Operation:Tubular motor:To suit 230-volt nominal, 1 phase supply.External safety brake.Low level keyswitch.Direct drive motor:To suit 400-volt nominal, 3 phase supply.Integrated safety brake.Open, close, stop push buttons within low level control panel.Arrangement:Internally face fixed to timber, brick, block, concrete or steel (i.e. flexible and rigid structures).Locking:A pair of side guide mounted pin locks are provided.Over 5000 mm clear width, a centrally mounted ground lock (complete with padlock) is also provided. Size parameters:Maximum (width x height): 7 x 7 m (Insulated laths); 9 x 9 m (Single skin lath); 7 x 4 m (Tube motor).Minimum (width x height): 1 x 1 m.Weight:Varies with opening size dependent on lath/barrel/casing requirements but approximately 45 kgs/m².A1 Rated SecRoll SR1:Operation:Tubular motor:To suit 230-volt nominal, 1 phase supply.External safety brake.Low level keyswitchDirect drive motor:To suit 400-volt nominal, 3 phase supplyIntegrated safety brake.Open, close, stop push buttons within low level control panel.Arrangement:Internally face fixed to timber, brick, block, concrete or steel (i.e. flexible and rigid structures).Locking:A pair of side guide mounted pin locks are provided.Size parameters:Maximum (width x height): 7 x 7 m (Direct drive motor); 7 x 4 m (Tube motor).Minimum (width x height): 1 x 1 m.Weight:Varies with opening size dependent on lath/barrel/casing requirements but approximately 45 kgs/m².Performance characteristics:LPS1175 Issue 7 security standards—SR1, SR2 & SR3 options.Resistance to Wind—Class 5Options for:Thermal Resistance – 1.1 W/(m²K) at centre / 3.2 W/(m²K) at quirksSound Reduction – 18 dB Rw (BS EN ISO 10140-2:2010 – Measurements of Airborne Sound Insulation) Key attributes:LPS 1175 Approved Security Rating.High wind load capability.Can provide both thermal and acoustic properties.Bespoke manufacture to suit individual opening sizes.   Roller shutters

Published [30/03/2026]