What is Internal Tanking?
July 2021

‘Tanking’ is a term used to describe internal or external waterproof barriers that are used to protect below ground structures from water ingress.

The British Standard for Waterproofing 8102:2009; ‘The Code of Practice for the Protection of Below Ground Structures from Water in the Ground’ refers to these waterproof barriers as ‘Type A Systems’.

Type A waterproofing systems can be applied either:

- Internally (on the negative side) such as the Newton HydroSeal System
- Or externally (on the positive side) such as the Newton HydroBond System

Waterproof barrier membranes that can be applied to the internal side of a below-ground structure are typically liquid-applied membranes or slurries that can be applied using a brush, roller, trowel, or spray machine directly to the surface.

As these internal tanking products are required to actively hold back water, it is important to identify the best product to use and prepare the surface correctly.

When a completely dry internal environment is required, Newton recommends a combined waterproofing solution utilising Type A and/or Type B, as well as a failsafe Type C system.

How do you Tank an Internal Wall?

To decide on the best internal tanking solution, system or product it is necessary to consider the guidelines set out in BS 8102:2009 and the technical standard documents of your insurance company, where they explain the typical defects that could occur in waterproofing systems, such as;

- defects owing to the specific properties of the materials being used
- defects owing to poor workmanship
- defects owing to the inappropriate use of materials

Traditional Tanking

Traditionally, bituminous barrier materials were used internally and had to be sandwiched within a further internal construction to hold them tight against the existing structure in an attempt to hold back the hydrostatic pressure.

Inevitably, the internal holding structure would include voids, whereby the bituminous product would bulge under pressure from water and then rupture, causing water ingress. Consequently, these products evolved into polymer-modified bitumen, manufactured as self-adhesive or torch-applied sheet membranes.

However, with these products, the water would still track freely behind the membrane and enter the internal space at poor laps.

The defects that typically occur from cutting, splicing, and sticking sheet membranes at awkward transitions and corners are often associated with poor workmanship and the specific properties of the material itself, thus indicating that this traditional membrane is inappropriate for use.

Internal Tanking Best Practice

The British Standard for Waterproofing advises that the issue of repairability should also be considered, and the feasibility of remedial measures assessed, to ensure that any of the aforementioned defects are avoided with the methods and materials that are used within the internal waterproofing solution.

This means that any potential defects or system failures that could arise should be taken into account as part of the overall waterproofing design for the structure.

- Large-internal-tanking-installation
- Newton 107F, a cementitious flexible waterproofing membrane.

Many insurers accept the advice given in BS 8102:2009, which outlines the effects of a bonded or partially bonded barrier and have now differentiated between the systems. Thus, where a structure is subjected to water pressure, only a fully bonded system should be used.

A fully bonded system can withstand the counter thrust or negative water pressure and prevent water from tracking into the internal area. Newton’s cementitious and liquid-applied products within the HydroSeal System can be used to meet these requirements and can better achieve a homogenous internal tanking solution with no physical laps.

The Newton HydroSeal System includes a range of cementitious products to provide a fully bonded solution. The range varies between products that use hydrophobic additives such as the Newton 908 LiquaBond added to a standard sand/cement mix, products that use polymer-modified cements such as the Newton 203-RM and Newton 105, and epoxy or acrylic resins including Newton 110 WATstop, Newton 103-S and Newton 107F, which offer varying degrees of hardness, flexibility, and chemical/gas resistance to ensure that the requirements of the project design are met.

If you are involved in an upcoming waterproofing project that requires a comprehensive internal tanking solution, designed and guaranteed by industry experts, please contact our Technical Team using the form below, by calling 01732 280680 or emailing tech@newtonwaterproofing.co.uk.